| 1 | Steel Tape, 10 m length | |
| 2 | Plier Insulated, 150 mm | |
| 4 | Plier Side Cutting, 150 mm | |
| 5 | Screw Driver, 100 mm | |
| 6 | Screw Driver, 150 mm | |
| 7 | Electrician Connector, screw driver insulated handle thin stem, 100 mm | |
| 8 | Heavy Duty Screw Driver , 200 mm | |
| 9 | Electrician Screw Driver thin stem insulated handle, 250 mm | |
| 10 | Punch Centre , 150 mm X 9 mm | |
| 11 | Knife Double Bladed Electrician | |
| 12 | Neon Tester | |
| 13 | Steel Rule 300 mm | |
| 14 | Hammer, cross peen with handle | |
| 15 | Hammer, ball peen With handle | |
| 16 | Gimlet 6 mm. | |
| 17 | Bradawl | |
| 18 | Scriber (Knurled centre position ) | |
| 19 | Pincer 150 mm | |
| 20 | C- Clamp 200 mm, 150 mm and 100 mm | |
| 21 | Spanner Adjustable 150 mm, 15 degree | |
| 22 | Blow lamp 0.5 ltr | |
| 23 | Melting Pot | |
| 24 | Ladel | |
| 25 | Chisel Cold firmer 25 mm X 200 mm | |
| 26 | Chisel 25 mm & 6 mm | |
| 27 | Hand Drill Machine 0 to 6 mm capacity | |
| 28 | Portable Electric Drill Machine 6 mm capacity | |
| 29 | Pillar Electric Drill Machine 12 mm capacity | |
| 30 | Allen Key | |
| 31 | Oil Can 0.12 ltr | |
| 32 | Grease Gun | |
| 33 | Out Side Micrometer 0 to 25 mm | |
| 34 | Motorised Bench Grinder | |
| 35 | Rawl plug tool & bit | |
| 36 | Pully Puller | |
| 37 | Bearing Puller | |
| 38 | Hygrometer | |
| 39 | Thermometer 0 to 100 deg Centigrade | |
| 40 | Scissors blade 150 mm | |
| 41 | Crimping Tool | |
| 42 | Wire stripper 20 cm | |
| 43 | Chisel Cold flat 12 mm | |
| 44 | Mallet hard wood 0.50 kg | |
| 45 | Hammer Exeter type 0.40 kg | |
| 46 | Hacksaw frame 200 mm 300 mm adjustable | |
| 47 | Try Square 150 mm blade | |
| 48 | Outside & Inside Divider Calliper | |
| 49 | Pliers flat nose 150 mm | |
| 50 | Pliers round nose 100 mm | |
| 51 | Tweezers 100 mm | |
| 52 | Snip Straight & Bent 150 mm | |
| 53 | D.E. metric Spanner | |
| 54 | Drill hand brace 0 to 100 mm | |
| 55 | Drill S.S. Twist block 2 mm, 5 mm 6 mm set of 3 | |
| 56 | Plane, smoothing cutters 50 mm | |
| 57 | Gauge, wire imperial | |
| 58 | File flat 200 mm 2nd cut | |
| 59 | File half round 2 00 mm 2nd cut | |
| 60 | File round 200 mm 2nd cut | |
| 61 | File flat 150 mm rough | |
| 62 | File flat 250 mm bastard | |
| 63 | File flat 250 mm smooth | |
| 64 | File Rasp, half round 200 mm bastard | |
| 65 | Soldering Iron 25 watt, 65 watt, 125 watt | |
| 66 | Copper bit soldering iron 0.25 kg. | |
| 67 | Desoldering Gun | |
| 68 | Hand Vice 50 mm jaw | |
| 69 | Table Vice 100 mm jaw | |
| 70 | Pipe Cutter to cut pipes upto 5 cm. dia | |
| 71 | Pipe Cutter to cut pipes above 5 cm dia | |
| 72 | Stock and Die set for 20 mm to 50 mm G.I. pipe | |
| 73 | Ohm Meter; Series Type & Shunt Type | |
| 74 | Stock and Dies conduit | |
| 75 | Multi Meter (analog) 0 to 1000 M Ohms, 2.5 to 500 V | |
| 76 | Digital Multi Meter | |
| 77 | A.C. Voltmeter M.I. 0 –500V A.C | |
| 78 | Milli Voltmeter centre zero 100 – 0 – 100 m volt | |
| 79 | D.C. Milliammeter 0 -500m A | |
| 80 | Ammeter MC 0-5 A, 0- 25 A | |
| 81 | A.C. Ammeter M.I.. 0-5A, 0-25 A | |
| 82 | Kilo Wattmeter 0-1-3 kw | |
| 83 | A.C. Energy Meter,Single phase 5 amp. Three Phase 15 amp | |
| 84 | Power Factor Meter | |
| 85 | Frequency Meter | |
| 86 | Tachometer with watch | |
| 87 | Current Transformer | |
| 88 | Potential Transformer | |
| 89 | Growler | |
| 90 | Tong Tester / Clamp Meter 0 – 100 amp. AC | |
| 91 | Megger 500 volts | |
| 92 | Wheat Stone Bridge with galvanometer & battery | |
| 93 | Contactor & auxiliary contacts 3 phase, 440volt, 16amp | |
| 94 | Contactor & auxiliary contacts 3 phase, 440 volt, 32 amp. | |
| 95 | Limit Switch | |
| 96 | Rotary Switch 16 A | |
| 97 | Load Bank5 KW( Lamp / heater Type) | |
| 98 | Brake Test arrangement with two spring balance 0 to 25 kg rating | |
| 99 | Knife Switch DPDT fitted with fuse terminals 16 amp | |
| 100 | Knife Switch TPDT fitted with fuse terminals 16 amp | |
| 101 | DC Power Supply | |
| 102 | Inverter- 1 KVA with 12 V Battery | |
| 103 | Input- 12 volt DC, | |
| 104 | Output- 220 volt AC | |
| 105 | Voltage Stabiliser | |
| 106 | Input: 150 – 230 volt AC | |
| 107 | Output: 220 volt AC | |
| 108 | Rheostat | |
| 109 | 0 -1 Ohm, 5 Amp | |
| 110 | 0 -10 Ohm, 5 Amp | |
| 111 | 0- 25 Ohm, 1 Amp | |
| 112 | 0- 300 Ohm, 1 Amp | |
| 113 | Domestic Appliances – | |
| 114 | a. Electric Hot Plate 1500 watt | |
| 115 | b. Electric Kettle, 100 watts | |
| 116 | c. Electric Iron 1200 watts | |
| 117 | d. Immersion Heater 500/100/2000 watt | |
| 118 | e. A.C. Fan | |
| 119 | f. Geyser (Storage type) 15 ltr minimum | |
| 120 | g. Mixture & Grinder | |
| 121 | Flux meter | |
| 122 | Laboratory Type Induction Coil | |
| 123 | 3- point D.C. Starter | |
| 124 | 4- point D.C. Starter | |
| 125 | Relaysa. | |
| 126 | Cut out | |
| 127 | b. Reverse current | |
| 128 | c. Over current | |
| 129 | d. Over load | |
| 130 | e. Under voltage | |
| 131 | Starters for 2 to 5 H.P. A.C Motorsa. | |
| 132 | Resistance type starter | |
| 133 | b. Direct on line Starter | |
| 134 | c. Star Delta Starter- manual, semi-automatic and automatic | |
| 135 | d. Auto Transformer type | |
| 136 | Electrical Machine Trainer – | |
| 137 | Suitable for demonstrating the construction and functioning of different types of DC machines and AC machines (single phase and three phase). Should be fitted with friction brake arrangement, dynamo meter, instrument panel and power supply unit | |
| 138 | | |
| 139 | Motor-Generator (AC to DC) consisting of : | |
| 140 | Squirrel Cage Induction Motor with star delta starter and directly coupled to DC shunt generator and switch board mounted with regulator, air breaker, ammeter, voltmeter, knife blade switches and fuses, set complete with case iron and plate, fixing bolts, foundation bolts and flexible coupling. | |
| 141 | Induction Motor rating: | |
| 142 | 7 HP, 400V, 50 cycles, 3 phase DC Shunt Generator rating: 5 KW, 440V | |
| 143 | Motor Generator(DC to AC) set consisting of - | |
| 144 | Shunt Motor with starting compensator and switch directly coupled to AC generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. Set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling | |
| 145 | Shunt Motor rating : 5 HP, 440V AC Generator rating : 3-Phase, 4 wire, 3.5 KVA, 400/230 Volts, 0.8 pf, 50cycles | |
| 146 | Used DC Generators-series, shunt and compound type for overhauling practice | |
| 147 | D.C. Shunt Generator with control panel, 2.5 KW, 230 V | |
| 148 | D.C. Compound Generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, 2.5 KW, 230 V | |
| 149 | Diesel Generator Set with change over switch, over current breaker and water-cooled with armature, star-delta connections AC 3 phase, 5 KVA, 230 volt | |
| 150 | DC Series Motor coupled with mechanical load 0.5 to 2 HP, 220 Volts | |
| 151 | DC Shunt Motor 2 to 3 HP, 220 volts | |
| 152 | DC compound Motor with starter and switch 2 to 3 HP, 220 volts | |
| 153 | AC Squirrel Cage Motor with star delta starter and triple pole iron clad switch fuse. 2 to 3 HP, 3-phase ,400 volts, 50 cycles | |
| 154 | AC phase-wound slip ring Motor with starter and switch 5 HP, 400 volts, 3-phase, 50 cycles | |
| 155 | A.C. Series type Motor with mechanical load ¼ HP, 230V, 50 cycles | |
| 156 | Single Phase Capacitor Motor with starter switch 1 HP 230 volt 50 cycles | |
| 157 | Universal Motor with starter/switch 230 volt, 50 cycles ¼ HP | |
| 158 | Stepper Motor with Digital Controller | |
| 159 | Shaded Pole Motor | |
| 160 | Single phase Transformer, core type, air cooled | |
| 161 | Three phase transformer, shell type oil cooled | |
| 162 | Variable Auto Transformer | |
| 163 | Oscilloscope Dual Trace,30 MHZ | |
| 164 | Function Generator | |
| 165 | Discrete Component Trainer | |
| 166 | Linear I.C.Trainer | |
| 167 | Digital I.C.Trainer | |
| 168 | Bath Impregnating | |
| 169 | Oven Stove | |
| 170 | Oil Testing Kit | |
| 171 | Battery Charger | |
| 172 | Hydrometer | |
| 173 | Air Breaker 5 KVA | |
| 174 | Miniature Breaker 16 amp | |
| 175 | Thyristor/IGBT controlled D.C. motor drive with tacho-generator feedback arrangement. 1 HP | |
| 176 | Thyristor/IGBT controlled A.C. motor drive with VVVF control 3 Phase, 2 HP | |
| 177 | Working Bench 2.5 m x 1.20 m x 0.75 m | |
| 178 | Fire Extinguisher | |
| 179 | Fire Buckets | |
| 180 | Instructor’s table | |
| 181 | Instructor’s chair | |
| 182 | Metal Rack 100cm x 150cm x 45cm | |
| 183 | Lockers with 16 drawers standard size | |
| 184 | Almirah 2.5 m x 1.20 m x 0.5 m | |
| 185 | Black board/white board | |
Send Inquiry
